Outdoor Ceiling Fans

Posted on

Hampton Bay Largo 48 In Indooroutdoor Gilded Iron Ceiling Fan inside sizing 1000 X 1000Hampton Bay Largo 48 In Indooroutdoor Gilded Iron Ceiling Fan inside sizing 1000 X 1000


Outdoor Ceiling Fans – The flush-style ceiling fan is mounted snugly next to a designated horizontal fairly low ceiling where it’s dealt with, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the instruments and possible other regions essential for installing them, their self-assemble kits include everything else. In many cases, the fan, that will have a unique lighting, will replace a ceiling fitting.

Safety, The electricity have to be off once your there the place that the fan is to be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker as well as flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; don’t lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, as appropriate

Installation steps (reading the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws through the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this fixture are cold (quality light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect these to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness of the electrical box inside ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box for the children. The ceiling fan is heavier compared to the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket on the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor plus a blue or off-color one for that lights to become attached below it. Overlap the stripped ends of such two wires (motor and lights) together while using stripped end of the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.


Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of such nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) on the electrical box if your box is also grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist about this green wire connection. Some will say to let it rest be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends of the mounting bracket while using small screws provided. It covers/hides the sides of the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades on the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to maintain them separate through the rest of the kit hardware.

Tip: to maintain the motor from becoming too off-level within this step, install the blades individually opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just below the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly is just not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on while using wall switch, as the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.