Popular Ceiling Fans

Posted on

Home Decorators Collection Altura 48 In Indooroutdoor Bronze intended for proportions 1000 X 1000Home Decorators Collection Altura 48 In Indooroutdoor Bronze intended for proportions 1000 X 1000


Popular Ceiling Fans – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it is out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the equipment and possible other areas needed for installing them, their self-assemble kits include the rest. In many cases, the fan, that will have its own lighting, will replace a ceiling fitting.

Safety, The electricity have to be off once your there in which the fan is usually to be installed. If the fan is replacing a fitting, de-activate its fuse or circuit breaker in addition to flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; don’t lean or get into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed

Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the fitting from the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this fixture are cold (the test light will always be off). Cut the wires, leaving 3-5″ of tail for connecting the crooks to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also look into the firmness with the electrical box inside the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes inside the box for the children. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside the junction box cleanly, install the mounting bracket towards the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor as well as a blue or off-color one for that lights being attached below it. Overlap the stripped ends of such two wires (motor and lights) together using the stripped end with the black ceiling wire inside the box, and twist connect them together using the wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same.


Then, to maintain these connections from loosening even though the fan is working, tape the wide lower ends of such nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) towards the electrical box in the event the box is also grounded using a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a specialist about it green wire connection. Some will say to let it rest be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends with the mounting bracket using the small screws provided. It covers/hides the edges with the motor and also the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets using the screws and washers provided. Then mount the blades towards the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to maintain them separate from the rest with the kit hardware.

Tip: to maintain the motor from becoming too off-level in this step, install the blades one at a time opposite to one another first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just beneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided in the event the lighting assembly is just not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on using the wall switch, even though the fan itself is controlled by the pull-chain switch only, initially set inside the off position. Note: The ceiling fan has a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.