Windmill Ceiling Fan With Light Kit – The flush-style ceiling fan is mounted snugly beside a flat horizontal fairly low ceiling where it really is out of the way, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the various tools and possible the rest needed for installing them, their self-assemble kits feature any devices. In many cases, the fan, that may have its lighting, will replace a ceiling light fixture.
Safety, The electricity has to be off once your there the location where the fan shall be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker as well as flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; usually do not lean or end up in a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if necessary
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture from the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect these to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one and a white one. Tip: also look at the firmness with the electrical box inside ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box for the children. The ceiling fan is heavier compared to the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in to the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor and a blue or off-color one for that lights to become attached below it. Overlap the stripped ends of the two wires (motor and lights) together with all the stripped end with the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same.
Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of the nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) on the electrical box when the box can be grounded having a third bare or green wire. Otherwise, when the electrical box in not grounded, ask a specialist relating to this green wire connection. Some will say to leave it be, i.e., do nothing from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends with the mounting bracket with all the small screws provided. It covers/hides the edges with the motor and the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate from the rest with the kit hardware.
Tip: to help keep the motor from becoming too off-level with this step, install the blades individually opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just below the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided when the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with all the wall switch, even though the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.