Hunter Fan 52 In Rustic Ceiling Fan With Clear Glass Led Light Kit for measurements 1000 X 1000Clear Glass Ceiling Fan – The flush-style ceiling fan is mounted snugly close to an appartment horizontal fairly low ceiling where it can be off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the various tools and possible other areas needed for installing them, their self-assemble kits include the rest. In many cases, the fan, that will have a unique lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off to begin the location where the fan will be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker together with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; do not lean or enter into a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the light fixture in the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws in the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (test light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect them to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one and a white one. Tip: also look at the firmness in the electrical box within the ceiling. If it can be not solidly connected to the ceiling, add two extra screws to its top side, that might require drilling two holes within the box for them. The ceiling fan is heavier compared to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires within the junction box cleanly, install the mounting bracket on the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor and a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end in the black ceiling wire within the box, and twist connect them together while using wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.
Then, to help keep these connections from loosening whilst the fan is working, tape the wide lower ends of these nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) on the electrical box if the box can be grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a specialist about this green wire connection. Some will say to let it rest be, i.e., do nothing from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends in the mounting bracket while using small screws provided. It covers/hides the sides in the motor and the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets while using screws and washers provided. Then mount the blades on the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate in the rest in the kit hardware.
Tip: to help keep the motor from becoming too off-level in this step, install the blades one at a time opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just beneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly just isn’t wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on while using wall switch, whilst the fan itself is controlled from the pull-chain switch only, initially set within the off position. Note: The ceiling fan includes a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.
