Prominence Home Ceiling Fan Palm Island Tropical Palm Leaf Blade pertaining to proportions 1400 X 1400Island Style Ceiling Fans – The flush-style ceiling fan is mounted snugly alongside a designated horizontal fairly low ceiling where it really is off the beaten track, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the tools and possible other areas essential for installing them, their self-assemble kits feature any devices. In many cases, the fan, which will have its lighting, will replace a ceiling fitting.
Safety, The electricity must be off once your there where the fan shall be installed. If the fan is replacing a fitting, shut down its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; don’t lean or end up in a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, as appropriate
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws through the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections for this fixture are cold (test light will always be off). Cut the wires, leaving 3-5″ of tail for connecting the crooks to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one and a white one. Tip: also confirm the firmness in the electrical box within the ceiling. If it really is not solidly attached to the ceiling, add two extra screws to its top side, which can require drilling two holes within the box on their behalf. The ceiling fan is heavier compared to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires within the junction box cleanly, install the mounting bracket towards the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor and a blue or off-color one for that lights being attached below it. Overlap the stripped ends of those two wires (motor and lights) together using the stripped end in the black ceiling wire within the box, and twist connect them together using the wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) towards the electrical box in the event the box can also be grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a specialist about it green wire connection. Some will say to let it sit be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends in the mounting bracket using the small screws provided. It covers/hides the edges in the motor along with the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets using the screws and washers provided. Then mount the blades towards the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to maintain them separate through the rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level within this step, install the blades individually opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just beneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, as the fan itself is controlled through the pull-chain switch only, initially set within the off position. Note: The ceiling fan carries a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.
