Hunter Contempo Ceiling Fan

Posted on

Hunter Contempo 52 In Indoor Brushed Nickel Ceiling Fan With pertaining to sizing 1000 X 1000Hunter Contempo 52 In Indoor Brushed Nickel Ceiling Fan With pertaining to sizing 1000 X 1000


Hunter Contempo Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it’s taken care of, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the equipment and possible the rest necessary for installing them, their self-assemble kits have everything else. In many cases, the fan, that can have its very own lighting, will replace a ceiling permanent fixture.

Safety, The electricity have to be off at the site the location where the fan shall be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if required

Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture through the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws through the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections for this fixture are cold (the exam light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one as well as a white one. Tip: also look at the firmness in the electrical box inside the ceiling. If it’s not solidly connected to the ceiling, add two extra screws to its top side, which could require drilling two holes inside the box for the kids. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside the junction box cleanly, install the mounting bracket on the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor as well as a blue or off-color one for that lights to get attached below it. Overlap the stripped ends of such two wires (motor and lights) together with the stripped end in the black ceiling wire inside the box, and twist connect them together with the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same way.


Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of such nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) on the electrical box if your box is additionally grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist about it green wire connection. Some will say to get forced out be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends in the mounting bracket with the small screws provided. It covers/hides the sides in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades on the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate through the rest in the kit hardware.

Tip: to help keep the motor from becoming too off-level in this step, install the blades individually opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just underneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if your lighting assembly just isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with the wall switch, even though the fan itself is controlled with the pull-chain switch only, initially set inside the off position. Note: The ceiling fan has a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.