Home Decorators Collection Gardinier 52 In Led Indoor Brushed throughout dimensions 1000 X 1000Gardinier Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a designated horizontal fairly low ceiling where it is taken care of, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the room size being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the instruments and possible other regions required for installing them, their self-assemble kits come with anything else. In many cases, the fan, that can have its own lighting, will replace a ceiling permanent fixture.
Safety, The electricity have to be off once your there in which the fan shall be installed. If the fan is replacing a permanent fixture, turn off its fuse or circuit breaker along with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from your electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this particular fixture are cold (the test light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect them to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness of the electrical box in the ceiling. If it is not solidly connected to the ceiling, add two extra screws to its top side, which might require drilling two holes in the box for the children. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires in the junction box cleanly, install the mounting bracket to the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger into the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor plus a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together using the stripped end of the black ceiling wire in the box, and twist connect them together using the wire nut provided. Connect the white assembly wire to the white ceiling wire much the same way.
Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box if the box can be grounded which has a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a specialist concerning this green wire connection. Some will say to get forced out be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends of the mounting bracket using the small screws provided. It covers/hides the perimeters of the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets using the screws and washers provided. Then mount the blades to the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to help keep them separate from your rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level during this step, install the blades one-by-one opposite to each other to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if the lighting assembly is not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on using the wall switch, even though the fan itself is controlled from the pull-chain switch only, initially set in the off position. Note: The ceiling fan includes a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.
