Belt Driven Steampunk Ceiling Fan Randolph Indoor And Outdoor Design pertaining to proportions 4288 X 2848Steampunk Ceiling Fan – The flush-style ceiling fan is mounted snugly beside a flat horizontal fairly low ceiling where it’s out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the instruments and possible other regions required for installing them, their self-assemble kits feature everything else. In many cases, the fan, that may have a unique lighting, will replace a ceiling light fixture.
Safety, The electricity should be off to begin the place that the fan is usually to be installed. If the fan is replacing a light fixture, shut down its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; tend not to lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, as appropriate
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture in the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws in the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this particular fixture are cold (test light will stay off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness of the electrical box in the ceiling. If it’s not solidly connected to the ceiling, add two extra screws to its top side, which might require drilling two holes in the box for them. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires in the junction box cleanly, install the mounting bracket for the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger in to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor as well as a blue or off-color one for the lights to be attached below it. Overlap the stripped ends of those two wires (motor and lights) together with the stripped end of the black ceiling wire in the box, and twist connect them together with the wire nut provided. Connect the white assembly wire for the white ceiling wire the same way.
Then, to help keep these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) for the electrical box in the event the box is additionally grounded with a third bare or green wire. Otherwise, in the event the electrical box in not grounded, ask a professional about it green wire connection. Some will say to leave it be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends of the mounting bracket with the small screws provided. It covers/hides the perimeters of the motor along with the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades for the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to help keep them separate in the rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level within this step, install the blades one at a time opposite to one another first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided in the event the lighting assembly is not wanted without any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with the wall switch, whilst the fan itself is controlled by the pull-chain switch only, initially set in the off position. Note: The ceiling fan carries a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.
