Hunter Channelside 52 In Led Indooroutdoor Noble Bronze Ceiling regarding size 1000 X 1000Hunter Ceiling Fans With Remote Control Included – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it really is dealt with, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible other parts required for installing them, their self-assemble kits have any devices. In many cases, the fan, that will have its lighting, will replace a ceiling fitting.
Safety, The electricity has to be off once your there the location where the fan will be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker along with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; usually do not lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the fitting from your ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws from your electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections for this fixture are cold (test light will stay off). Cut the wires, leaving 3-5″ of tail in order to connect the crooks to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one as well as a white one. Tip: also look into the firmness in the electrical box within the ceiling. If it really is not solidly attached to the ceiling, add two extra screws to its top side, which might require drilling two holes within the box for the kids. The ceiling fan is heavier compared to the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires within the junction box cleanly, install the mounting bracket to the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of such two wires (motor and lights) together using the stripped end in the black ceiling wire within the box, and twist connect them together using the wire nut provided. Connect the white assembly wire to the white ceiling wire the same way.
Then, to maintain these connections from loosening whilst the fan is working, tape the wide lower ends of such nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box if the box is also grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an experienced about this green wire connection. Some will say to get forced out be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends in the mounting bracket using the small screws provided. It covers/hides the edges in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets using the screws and washers provided. Then mount the blades to the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate from your rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level within this step, install the blades one at a time opposite together first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just beneath the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, whilst the fan itself is controlled from the pull-chain switch only, initially set within the off position. Note: The ceiling fan has a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.
