Ceiling Fan Mount – Two top reasons to install a ceiling fan, heating and cooling. If you live in a very cold climate, fans can push hot air gathered close to the ceiling down again. Ceiling fans could be easy to install when you have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already includes a light fixture inside ceiling, your light fixture probably has one hot or feed wire going to it, the neutral white along with the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for the light the other for the fan motor control along with the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans work together with your application. Additionally some remote-controlled fans use wall controller which sends its signal for the fan being a TV remote. It just appears to be a wall control unit. If you really need the power wire to your remote-controlled fan, please cap over fourth wire which you will not need to use. This ought to be shown in your directions that had the fan assembly.
Once you have acquired a lover you like, build it according for the instructions given. Some fans are a little more complex, ask a buddy to assist if you need to. It is best to makes it assembled correctly, using a ceiling fan blade thud yourself the top could be annoying. Once you have the pre-assembly completed, now you can prepare the ceiling junction box. Of course I know you have already made certain the power for the ceiling box is switched off with no you can energize it accidentally. Once you have performed this, you must find three wires inside J-box. A copper or green wire for bonding. A white wire for the neutral and a red or black wire for the power. If your junction box includes a fourth wire, this could be create for any wall controlled fan switch which is great and allows you to use a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so you shouldn’t be confused because these all work with the singular feed in your ceiling junction box.
A word about weight, not yours but anything in regards to the height and width of your fan. If you have a substantial fan and its particular weighted near 12 pounds or more, you need a special junction box that could keep the extra body fat. I would recommend you ask someone who knows about these heavier fans you might need what you really are going to install. Most fans are lighter and could be positioned in most junction boxes without modifications.
Now we should get it up there, the fan which is. Many fans include a Hanger shaped like a U. Install this hanger on your box, the screws ought to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, pick up your fan motor devoid of the blades installed and hang up it around the hanger. This allows you the electrician to attach the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire for the chassis as noted inside instructions. Next connect the white neutral wire, now the black wire. Swing the fan into place while using the parts provided. Some have brackets, some use a metal plate while others use preformed mounting bases. Use your instructions you may have a lover quickly. Smaller fans might require that you pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is less difficult. It does require however, that you work above your head to find the blades attached.
Once you have the fan hanging, the blades installed and everything tightened now you can step over ladder, take a deep breath, then install the wall controller as provided. These all vary in design nevertheless they all follow similar procedures. Remember, you’ll have a line and load situation here. This means, the line side could be the list of wires the feed in the switch box through the panel whilst the Load side is going to your fan. This is critical so make sure you view the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be composed for the new controller. Next wire your white neutral for the controllers neutral for the Line side. You may have already wired your neutrals together in accordance with your instructions. Now wire your Hot or Power wire for the Line side of your controller. If you have the fourth wire in that room, cap rid of it or use it for the motor control and connect it accordingly in your directions. Red to Red is often the case here. Once completed, be some Iced Tea and revel in a new fan.