Propeller Ceiling Fan – Two top reasons to use a ceiling fan, heating and cooling. If you live inside a cold climate, fans can push warm air gathered at the ceiling back down. Ceiling fans may be an easy task to install in case you have some mechanical aptitude. Current ceiling fans have remote-controls to vary speed and adjust lighting. If your room already carries a light fixture within the ceiling, your light fixture probably has one hot or feed wire gonna it, the neutral white along with the bonding green or copper. Essentially it is a three-wire system. Many new construction homes have four wires available, one to the light and one to the fan motor control along with the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans works along with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan as being a TV remote. It just appears like a wall control unit. If you merely have the electricity wire for your remote-controlled fan, please cap off of the fourth wire which you will not want to work with. This ought to be shown in your directions that was included with the fan assembly.
Once you’ve got acquired a fan you prefer, build it according to the instructions given. Some fans can be a bit more complex, ask an associate to assist if required. It is best to help it become assembled correctly, creating a ceiling fan blade thud your self on the pinnacle may be annoying. Once you’ve got the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you’ve got already made certain the electricity to the ceiling box is deterred no one can energize it accidentally. Once you’ve got carried this out, you ought to find three wires within the J-box. A copper or green wire for bonding. A white wire to the neutral plus a red or black wire to the power. If your junction box carries a fourth wire, this could be setup to get a wall controlled fan switch that’s great and allows you to work with a non-remote wall controller. I should mention that some all fans have a wall controllers designed as remotes so don’t be confused because these all assist the singular feed in your ceiling junction box.
A word about weight, not yours but a thing concerning the size your fan. If you’ve got a large fan and its particular weighted near 12 pounds or higher, you will need a special junction box that may secure the more weight. I would recommend i hear you ask someone that knows about these heavier fans if that’s what you are gonna install. Most fans are lighter and may be positioned in most junction boxes without modifications.
Now let’s get up there, the fan which is. Many fans have a Hanger the same shape as a U. Install this hanger on to your box, the screws ought to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve got the hanger installed, pick-up your fan motor with no blades installed and it around the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it at the same time. Connect the bonding wire to the chassis as noted within the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place while using the parts provided. Some have brackets, some use a metal plate while some use preformed mounting bases. Use your instructions you’ll also find a fan right away. Smaller fans might require that you pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is much easier. It does require however, that you work above your brain to find the blades attached.
Once you’ve got the fan hanging, the blades installed and everything tightened you can now step off of the ladder, breathe deeply, then install the wall controller as provided. These all vary in design nonetheless they all follow similar procedures. Remember, you will have a line and load situation here. This means, the line side will be the group of wires the feed in to the switch box from your panel even though the Load side is gonna your fan. This is critical so be sure to understand the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform the Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral to the Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire to the Line side of your respective controller. If you’ve got the fourth wire inside, cap them back or use it to the motor control and connect it accordingly for a directions. Red to Red is often the case here. Once completed, be some Iced Tea and get your fan.