Barnwood Ceiling Fan – Two reasons to put in a ceiling fan, heating and cooling. If you live in a cold climate, fans can push heated air gathered close to the ceiling back down. Ceiling fans may be an easy task to install for those who have some mechanical aptitude. Current ceiling fans feature remote-controls to vary speed and adjust lighting. If your room already carries a permanent fixture inside the ceiling, your permanent fixture probably has one hot or feed wire likely to it, the neutral white along with the bonding green or copper. Essentially this can be a three-wire system. Many new construction homes have four wires available, one for your light then one for your fan motor control along with the neutral and ground. If you just have one Hot wire feeding the ceiling junction box, the remote-control fans works along with your application. Additionally some remote-controlled fans use wall controller which sends its signal for the fan being a TV remote. It just seems like a wall control unit. If you only need the ability wire for your remote-controlled fan, please cap from the fourth wire which you will n’t need to make use of. This ought to be shown within your directions that came with the fan assembly.
Once you’ve got acquired a fan you want, build it according for the instructions given. Some fans can be a bit more complex, ask a friend to aid if need be. It is best to make sure it is assembled correctly, having a ceiling fan blade thud yourself the head may be annoying. Once you’ve got the pre-assembly completed, it’s simple to prepare the ceiling junction box. Of course I know you’ve got already made sure the ability for the ceiling box is powered down and no it’s possible to energize it accidentally. Once you’ve got carried this out, you must find three wires inside the J-box. A copper or green wire for bonding. A white wire for your neutral and a red or black wire for your power. If your junction box carries a fourth wire, this may be build for any wall controlled fan switch that’s great and allows you to make use of a non-remote wall controller. I should mention that some all fans feature a wall controllers designed as remotes so don’t be confused because these all use the singular feed within your ceiling junction box.
A word about weight, not yours but a thing regarding the size your fan. If you’ve got a sizable fan and its weighted near 12 pounds or higher, you may need a special junction box that could support the excess weight. I would recommend you may well ask somebody that knows about these heavier fans if that’s what you really are likely to install. Most fans are lighter and may be positioned in most junction boxes without modifications.
Now let us get up there, the fan that is. Many fans feature a Hanger shaped like a U. Install this hanger on your box, the screws ought to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve got the hanger installed, grab your fan motor with no blades installed and hang up it about the hanger. This allows you the electrician to connect the wires without struggling to juggle the motor and wire it simultaneously. Connect the bonding wire for the chassis as noted inside the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place while using parts provided. Some have brackets, some work with a metal plate although some use preformed mounting bases. Use your instructions you’ll also find a fan in no time. Smaller fans might require that you pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is easier. It does require however, that you work above your brain to obtain the blades attached.
Once you’ve got the fan hanging, the blades installed and everything tightened it’s simple to step from the ladder, breathe deeply, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will find a line and load situation here. This means, the line side may be the set of wires the feed to the switch box in the panel even though the Load side is likely to your fan. This is critical so make sure you comprehend the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform the Line (incoming) side next: Bond or ground should already be constructed for the new controller. Next wire your white neutral for the controllers neutral for your Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire for the Line side of your controller. If you’ve got the fourth wire in that room, cap it well or use it for your motor control and connect it accordingly for your directions. Red to Red is usually the case here. Once completed, get yourself some Iced Tea and luxuriate in your fan.