Ceiling Fan Electrical Wiring – The flush-style ceiling fan is mounted snugly close to a flat horizontal fairly low ceiling where it is off the beaten track, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the various tools and possible other areas needed for installing them, their self-assemble kits come with anything else. In many cases, the fan, that will have its own lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off at the site the location where the fan is usually to be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; don’t lean or enter into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if needed
Installation steps (reading the fan installation instructions thoroughly). 1. Remove the permanent fixture through the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws through the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this fixture are cold (quality light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect these phones the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one along with a white one. Tip: also look into the firmness from the electrical box in the ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, that might require drilling two holes in the box for them. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires in the junction box cleanly, install the mounting bracket towards the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger in to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor along with a blue or off-color one to the lights to get attached below it. Overlap the stripped ends of such two wires (motor and lights) together while using stripped end from the black ceiling wire in the box, and twist connect them together while using wire nut provided. Connect the white assembly wire towards the white ceiling wire the same way.
Then, to help keep these connections from loosening whilst the fan is working, tape the wide lower ends of such nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) towards the electrical box if your box can be grounded with a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an experienced relating to this green wire connection. Some will say to let it rest be, i.e., relax by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends from the mounting bracket while using small screws provided. It covers/hides the sides from the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets while using screws and washers provided. Then mount the blades towards the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to help keep them separate through the rest from the kit hardware.
Tip: to help keep the motor from becoming too off-level with this step, install the blades one-by-one opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just beneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on while using wall switch, whilst the fan itself is controlled by the pull-chain switch only, initially set in the off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.