30 Ceiling Fan – The flush-style ceiling fan is mounted snugly alongside a flat horizontal fairly low ceiling where it’s dealt with, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the equipment and possible the rest needed for installing them, their self-assemble kits have everything else. In many cases, the fan, that may have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity have to be off at the site the place that the fan is to be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; usually do not lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws from the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections to this particular fixture are cold (test light will continue to be off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one and a white one. Tip: also look at the firmness with the electrical box within the ceiling. If it’s not solidly attached to the ceiling, add two extra screws to its top side, which can require drilling two holes within the box on their behalf. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires within the junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger into the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together using the stripped end with the black ceiling wire within the box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) for the electrical box when the box can be grounded with a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to let it sit be, i.e., relax by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends with the mounting bracket using the small screws provided. It covers/hides the sides with the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to help keep them separate from the rest with the kit hardware.
Tip: to help keep the motor from becoming too off-level in this step, install the blades one at a time opposite to each other first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just beneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided when the lighting assembly is not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, as the fan itself is controlled from the pull-chain switch only, initially set within the off position. Note: The ceiling fan includes a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.