Ceiling Fan Chandelier Combo – The flush-style ceiling fan is mounted snugly next to a flat horizontal fairly low ceiling where it really is off the beaten track, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the size of room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the instruments and possible the rest needed for installing them, their self-assemble kits come with the rest. In many cases, the fan, that will have its very own lighting, will replace a ceiling fitting.
Safety, The electricity should be off once your there the location where the fan shall be installed. If the fan is replacing a fitting, turn off its fuse or circuit breaker in addition to flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or end up in a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, as appropriate
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the fitting through the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws through the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to the fixture are cold (the exam light will always be off). Cut the wires, leaving 3-5″ of tail to get in touch these phones the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one plus a white one. Tip: also look into the firmness in the electrical box inside ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box on their behalf. The ceiling fan is heavier compared to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket for the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor plus a blue or off-color one to the lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end in the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to maintain these connections from loosening whilst the fan is working, tape the wide lower ends of these nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) for the electrical box when the box is additionally grounded using a third bare or green wire. Otherwise, when the electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to let it sit be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends in the mounting bracket while using small screws provided. It covers/hides the perimeters in the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After deciding on the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets while using screws and washers provided. Then mount the blades for the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to maintain them separate through the rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level during this step, install the blades one-by-one opposite together first of all. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just underneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided when the lighting assembly is not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, whilst the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan carries a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.