Ceiling Fan With Cord – The flush-style ceiling fan is mounted snugly beside a flat horizontal fairly low ceiling where it can be out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the equipment and possible other areas necessary for installing them, their self-assemble kits have the rest. In many cases, the fan, which will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off once your there in which the fan will be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker together with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder through the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (the test light will remain off). Cut the wires, leaving 3-5″ of tail allowing you to connect these to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one as well as a white one. Tip: also look into the firmness from the electrical box in the ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which might require drilling two holes in the box for them. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires in the junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights being attached below it. Overlap the stripped ends of the two wires (motor and lights) together with all the stripped end from the black ceiling wire in the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire exactly the same way.
Then, to keep these connections from loosening even though the fan is working, tape the wide lower ends of the nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) on the electrical box if the box is additionally grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an expert about this green wire connection. Some will say to get forced out be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket with all the small screws provided. It covers/hides the perimeters from the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to keep them separate from the rest from the kit hardware.
Tip: to keep the motor from becoming too off-level during this step, install the blades one-by-one opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just beneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if the lighting assembly just isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on with all the wall switch, even though the fan itself is controlled through the pull-chain switch only, initially set in the off position. Note: The ceiling fan includes a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.