Metal Ceiling Fan – Two top reasons to install a ceiling fan, cooling and heating. If you live in a very cold climate, fans can push warm air gathered near the ceiling back. Ceiling fans can be simple to install when you have some mechanical aptitude. Current ceiling fans have remote-controls to vary speed and adjust lighting. If your room already features a permanent fixture inside the ceiling, your permanent fixture probably has one hot or feed wire going to it, the neutral white and the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for your light then one for your fan motor control and the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans work along with your application. Additionally some remote-controlled fans use wall controller which sends its signal on the fan as being a TV remote. It just appears to be a wall control unit. If you only need the ability wire to your remote-controlled fan, please cap off the fourth wire which you will not require to utilize. This must be shown inside your directions that was included with the fan assembly.
Once you might have acquired a follower you prefer, put it together according on the instructions given. Some fans can be a bit more complex, ask a friend to aid if you need to. It is best to make sure it is assembled correctly, having a ceiling fan blade thud your self on the head can be annoying. Once you might have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you might have already made certain the ability on the ceiling box is deterred with out you can energize it accidentally. Once you might have performed this, you must find three wires inside the J-box. A copper or green wire for bonding. A white wire for your neutral and a red or black wire for your power. If your junction box features a fourth wire, this could be set up for any wall controlled fan switch which is great and allows you to utilize a non-remote wall controller. I should mention that some all fans have a wall controllers designed as remotes so you shouldn’t be confused because they all assist the singular feed inside your ceiling junction box.
A word about weight, not yours but a word about the size of your fan. If you might have a large fan as well as weighted near 12 pounds or higher, you need a special junction box that will support the more weight. I would recommend you ask someone that knows about these heavier fans recommendations what you’re going to install. Most fans are lighter and can be placed in most junction boxes without modifications.
Now we should get up there, the fan that’s. Many fans have a Hanger the same shape as a U. Install this hanger on your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, pick-up your fan motor minus the blades installed and hang up it on the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it concurrently. Connect the bonding wire on the chassis as noted inside the instructions. Next connect the white neutral wire, and today the black wire. Swing the fan into place using the parts provided. Some have brackets, some utilize a metal plate while some use preformed mounting bases. Use your instructions you may have a follower in no time. Smaller fans may need you to pre-assemble your blades before hanging the fan. I always found installing the motor first and then installing the blades last is much easier. It does require however, you to work above your brain to obtain the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened you can now step off the ladder, relax, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you’ll have a line and load situation here. This means, the queue side could be the set of wires the feed into the switch box from your panel while the Load side is going to your fan. This is critical so ensure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be comprised on the new controller. Next wire your white neutral on the controllers neutral for your Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire on the Line side of one’s controller. If you might have the fourth wire inside, cap rid of it or use it for your motor control and connect it accordingly in your directions. Red to Red is truly the case here. Once completed, be some Iced Tea and get your fan.