Hunter Ceiling Fan Downrod – Two top reasons to use a ceiling fan, air conditioning. If you live in a cold climate, fans can push hot air gathered near the ceiling down again. Ceiling fans can be an easy task to install in case you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already has a light fixture in the ceiling, your light fixture probably has one hot or feed wire planning to it, the neutral white as well as the bonding green or copper. Essentially this is a three-wire system. Many new construction homes have four wires available, one for that light the other for that fan motor control as well as the neutral and ground. If you have only one Hot wire feeding the ceiling junction box, the remote-control fans work along with your application. Additionally some remote-controlled fans use wall controller which sends its signal for the fan being a TV remote. It just appears like a wall control unit. If you really need the ability wire for your remote-controlled fan, please cap from the fourth wire which you will not want to use. This must be shown with your directions that had the fan assembly.
Once you have acquired a follower you like, put it together according for the instructions given. Some fans certainly are a extra complex, ask a buddy to help you if you need to. It is best to makes it assembled correctly, having a ceiling fan blade thud yourself on the head can be annoying. Once you have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you have already ensured the ability for the ceiling box is turned off with no you can energize it accidentally. Once you have performed this, you should find three wires in the J-box. A copper or green wire for bonding. A white wire for that neutral and a red or black wire for that power. If your junction box has a fourth wire, this would be build for any wall controlled fan switch which is great and allows you to use a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so don’t be confused as these all use the singular feed with your ceiling junction box.
A word about weight, not yours but anything about the size your fan. If you have a large fan and its particular weighted near 12 pounds or even more, you might need a special junction box that may secure the more weight. I would recommend you ask somebody who knows about these heavier fans if that’s what you are planning to install. Most fans are lighter and can be positioned in most junction boxes without modifications.
Now let us get up there, the fan that’s. Many fans come with a Hanger in the shape of a U. Install this hanger on to your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, pick up your fan motor without the blades installed and place it on the hanger. This allows you the electrician to connect the wires without struggling to juggle the motor and wire it concurrently. Connect the bonding wire for the chassis as noted in the instructions. Next connect the white neutral wire, now the black wire. Swing the fan into place with all the parts provided. Some have brackets, some utilize a metal plate although some use preformed mounting bases. Use your instructions you may have a follower quickly. Smaller fans might require you to definitely pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is less difficult. It does require however, you to definitely work above your mind to get the blades attached.
Once you have the fan hanging, the blades installed and everything tightened you can now step from the ladder, relax, then install the wall controller as provided. These all vary in design nevertheless they all follow similar procedures. Remember, you will find a line and load situation here. This means, the line side is the set of wires the feed in to the switch box from the panel even though the Load side is planning to your fan. This is critical so ensure you view the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be composed for the new controller. Next wire your white neutral for the controllers neutral for that Line side. You may have already wired your neutrals together in accordance with your instructions. Now wire your Hot or Power wire for the Line side of the controller. If you have the fourth wire inside, cap it well or use it for that motor control and connect it accordingly for a directions. Red to Red is truly the case here. Once completed, make yourself some Iced Tea and revel in a new fan.