Bulbs Ideas

Ceiling Fan Without Light Kit

Design House Millbridge 52 In Oil Rubbed Bronze Ceiling Fan With No for sizing 1000 X 1000

Design House Millbridge 52 In Oil Rubbed Bronze Ceiling Fan With No for sizing 1000 X 1000

Ceiling Fan Without Light Kit – The flush-style ceiling fan is mounted snugly beside an appartment horizontal fairly low ceiling where it is dealt with, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the room size being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the instruments and possible other regions essential for installing them, their self-assemble kits have everything else. In many cases, the fan, that will have its lighting, will replace a ceiling light fixture.

Safety, The electricity must be off at the site in which the fan will be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker along with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder throughout the installation; don’t lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed

Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture through the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws through the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (the exam light will stay off). Cut the wires, leaving 3-5″ of tail allowing you to connect them to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one and a white one. Tip: also look at the firmness in the electrical box within the ceiling. If it is not solidly connected to the ceiling, add two extra screws to its top side, that might require drilling two holes within the box on their behalf. The ceiling fan is heavier compared to the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires within the junction box cleanly, install the mounting bracket for the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger in the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights being attached below it. Overlap the stripped ends of those two wires (motor and lights) together while using stripped end in the black ceiling wire within the box, and twist connect them together while using wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.


Then, to hold these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) for the electrical box if the box can also be grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask a professional about this green wire connection. Some will say to let it rest be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends in the mounting bracket while using small screws provided. It covers/hides the perimeters in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 5) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets while using screws and washers provided. Then mount the blades for the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to hold them separate through the rest in the kit hardware.

Tip: to hold the motor from becoming too off-level in this step, install the blades one by one opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just beneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if the lighting assembly just isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on while using wall switch, whilst the fan itself is controlled through the pull-chain switch only, initially set within the off position. Note: The ceiling fan carries a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.

Exit mobile version