20 Inch Ceiling Fans – Two reasons to put in a ceiling fan, air conditioning. If you live in the cold climate, fans can push hot air gathered close to the ceiling down again. Ceiling fans can be easy to install for those who have some mechanical aptitude. Current ceiling fans have remote-controls to vary speed and adjust lighting. If your room already carries a fitting within the ceiling, your fitting probably has one hot or feed wire planning to it, the neutral white along with the bonding green or copper. Essentially this can be a three-wire system. Many new construction homes have four wires available, one for the light and something for the fan motor control along with the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans works with your application. Additionally some remote-controlled fans use wall controller which sends its signal for the fan just like a TV remote. It just seems like a wall control unit. If you only need the ability wire for your remote-controlled fan, please cap off of the fourth wire which you will not want to work with. This must be shown inside your directions that included the fan assembly.
Once you’ve acquired a fan you prefer, build it according for the instructions given. Some fans really are a much more complex, ask a buddy to help if you need to. It is best to help it become assembled correctly, using a ceiling fan blade thud yourself on the pinnacle can be annoying. Once you’ve the pre-assembly completed, anyone can prepare the ceiling junction box. Of course I know you’ve already ensured the ability for the ceiling box is turned off with out one can possibly energize it accidentally. Once you’ve carried this out, you need to find three wires within the J-box. A copper or green wire for bonding. A white wire for the neutral as well as a red or black wire for the power. If your junction box carries a fourth wire, this may be setup for any wall controlled fan switch that’s great and allows you to work with a non-remote wall controller. I should mention that some all fans have a wall controllers designed as remotes so don’t be confused because they all help the singular feed inside your ceiling junction box.
A word about weight, not yours but anything about the size of your fan. If you’ve a large fan and it is weighted near 12 pounds or higher, you may need a special junction box that will keep the excess weight. I would recommend you may ask someone who knows about these heavier fans if that is what you’re planning to install. Most fans are lighter and can be set up in most junction boxes without modifications.
Now we should get up there, the fan that is certainly. Many fans have a Hanger shaped like a U. Install this hanger onto your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve the hanger installed, grab your fan motor with no blades installed and hang up it about the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire for the chassis as noted within the instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place using the parts provided. Some have brackets, some utilize a metal plate and some use preformed mounting bases. Use your instructions you may have a fan right away. Smaller fans may necessitate that you pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is less difficult. It does require however, that you work above your mind to have the blades attached.
Once you’ve the fan hanging, the blades installed and everything tightened anyone can step off of the ladder, relax, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will have a line and load situation here. This means, the queue side may be the group of wires the feed into the switch box through the panel while the Load side is planning to your fan. This is critical so be sure you view the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be composed for the new controller. Next wire your white neutral for the controllers neutral for the Line side. You may have already wired your neutrals together based on your instructions. Now wire your Hot or Power wire for the Line side of one’s controller. If you’ve the fourth wire within, cap it off or use it for the motor control and connect it accordingly in your directions. Red to Red is often the case here. Once completed, make yourself some Iced Tea and get your brand-new fan.