Oil Rubbed Bronze Ceiling Fan Light Kit – Two top reasons to put in a ceiling fan, heating and cooling. If you live in a very cold climate, fans can push hot air gathered nearby the ceiling back off. Ceiling fans could be all to easy to install for those who have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already includes a light fixture inside ceiling, your light fixture probably has one hot or feed wire gonna it, the neutral white along with the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for your light the other for your fan motor control along with the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans works with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan being a TV remote. It just looks like a wall control unit. If you only need the power wire to your remote-controlled fan, please cap over fourth wire which you will not need to make use of. This ought to be shown with your directions that came with the fan assembly.
Once you’ve acquired a follower that suits you, assemble it according to the instructions given. Some fans can be a extra complex, ask a pal to assist if need be. It is best to help it become assembled correctly, using a ceiling fan blade thud your self on the pinnacle could be annoying. Once you’ve the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you’ve already ensured the power to the ceiling box is switched off and no one can possibly energize it accidentally. Once you’ve performed this, you should find three wires inside J-box. A copper or green wire for bonding. A white wire for your neutral plus a red or black wire for your power. If your junction box includes a fourth wire, this could be setup for the wall controlled fan switch that is great and allows you to make use of a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so don’t be confused because they all assist the singular feed with your ceiling junction box.
A word about weight, not yours but anything regarding the height and width of your fan. If you’ve a large fan and it is weighted near 12 pounds or maybe more, you might need a special junction box that may offer the additional weight. I would recommend i hear you ask somebody that knows about these heavier fans recommendations what you are gonna install. Most fans are lighter and could be set up in most junction boxes without modifications.
Now let us get up there, the fan that is. Many fans include a Hanger the same shape as a U. Install this hanger onto your box, the screws ought to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve the hanger installed, pick up your fan motor with no blades installed and hang up it about the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire to the chassis as noted inside instructions. Next connect the white neutral wire, now the black wire. Swing the fan into place while using parts provided. Some have brackets, some utilize a metal plate although some use preformed mounting bases. Use your instructions and you will have a follower right away. Smaller fans may need you to pre-assemble your blades before hanging the fan. I always found installing the motor first then installing the blades last is much simpler. It does require however, you to work above your brain to get the blades attached.
Once you’ve the fan hanging, the blades installed and everything tightened you can now step over ladder, take a deep breath, then install the wall controller as provided. These all vary in design however they all follow similar procedures. Remember, you will have a line and load situation here. This means, the queue side could be the list of wires the feed into the switch box from the panel as the Load side is gonna your fan. This is critical so be sure you comprehend the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral for your Line side. You may have already wired your neutrals together based on your instructions. Now wire your Hot or Power wire to the Line side of one’s controller. If you’ve the fourth wire in there, cap it off or use it for your motor control and connect it accordingly in your directions. Red to Red is truly the case here. Once completed, be some Iced Tea and enjoy a new fan.