Palm Leaf Ceiling Fan – Two good reasons to put in a ceiling fan, heating and cooling. If you live in the cold climate, fans can push hot air gathered nearby the ceiling back off. Ceiling fans could be all to easy to install for those who have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already features a light fixture inside ceiling, your light fixture probably has one hot or feed wire likely to it, the neutral white and the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for your light then one for your fan motor control and the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans will work together with your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan being a TV remote. It just seems like a wall control unit. If you merely have the energy wire for your remote-controlled fan, please cap from the fourth wire which you will not need to utilize. This must be shown with your directions that included the fan assembly.
Once you’ve acquired a follower that suits you, put it together according to the instructions given. Some fans are a much more complex, ask an associate to help if you need to. It is best to help it become assembled correctly, having a ceiling fan blade thud your self on the head could be annoying. Once you’ve the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you’ve already ensured the energy to the ceiling box is deterred and no you can energize it accidentally. Once you’ve done this, you should find three wires inside J-box. A copper or green wire for bonding. A white wire for your neutral and a red or black wire for your power. If your junction box features a fourth wire, this could be set up for the wall controlled fan switch that’s great and allows you to utilize a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so you shouldn’t be confused as these all use the singular feed with your ceiling junction box.
A word about weight, not yours but a word regarding the height and width of your fan. If you’ve a big fan and it is weighted near 12 pounds or higher, you will need a special junction box that will keep the extra body fat. I would recommend i hear you ask someone who knows about these heavier fans you might need what you will be likely to install. Most fans are lighter and could be installed in most junction boxes without modifications.
Now we should get it down there, the fan that’s. Many fans come with a Hanger the same shape as a U. Install this hanger onto your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve the hanger installed, pick up your fan motor devoid of the blades installed and hang it around the hanger. This allows you the electrician to attach the wires without struggling to juggle the motor and wire it simultaneously. Connect the bonding wire to the chassis as noted inside instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place while using parts provided. Some have brackets, some work with a metal plate while others use preformed mounting bases. Use your instructions you may have a follower quickly. Smaller fans may require that you pre-assemble your blades before hanging the fan. I always found installing the motor first after which installing the blades last is easier. It does require however, that you work above your mind to find the blades attached.
Once you’ve the fan hanging, the blades installed and everything tightened you can now step from the ladder, take a deep breath, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you will have a line and load situation here. This means, the queue side may be the list of wires the feed to the switch box in the panel whilst the Load side is likely to your fan. This is critical so ensure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform the Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral for your Line side. You may have already wired your neutrals together according to your instructions. Now wire your Hot or Power wire to the Line side of the controller. If you’ve the fourth wire in that room, cap them back or use it for your motor control and connect it accordingly for a directions. Red to Red is usually the case here. Once completed, be some Iced Tea and revel in a new fan.