Large Room Ceiling Fan – The flush-style ceiling fan is mounted snugly next to an appartment horizontal fairly low ceiling where it’s out of the way, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the room size being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the instruments and possible other areas required for installing them, their self-assemble kits include anything else. In many cases, the fan, that may have its own lighting, will replace a ceiling light fixture.
Safety, The electricity must be off at the site where the fan is to be installed. If the fan is replacing a light fixture, turn off its fuse or circuit breaker along with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; don’t lean or enter a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this fixture are cold (the test light will stay off). Cut the wires, leaving 3-5″ of tail to get in touch them to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one as well as a white one. Tip: also look into the firmness with the electrical box inside ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes inside box for the children. The ceiling fan is heavier as opposed to light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends with the tailing wires inside junction box cleanly, install the mounting bracket for the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside with the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger into the centralized holder with the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for that motor as well as a blue or off-color one for that lights to be attached below it. Overlap the stripped ends of such two wires (motor and lights) together while using stripped end with the black ceiling wire inside box, and twist connect them together while using wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to hold these connections from loosening whilst the fan is working, tape the wide lower ends of such nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) for the electrical box if your box can also be grounded which has a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist relating to this green wire connection. Some will say to get forced out be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends with the mounting bracket while using small screws provided. It covers/hides the perimeters with the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets while using screws and washers provided. Then mount the blades for the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to hold them separate from your rest with the kit hardware.
Tip: to hold the motor from becoming too off-level within this step, install the blades one-by-one opposite to one another in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just beneath the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly just isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on while using wall switch, whilst the fan itself is controlled through the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.