Bulbs Ideas

Ceiling Fan With Two Fans

Harbor Breeze Twin Breeze Ii 74 In Oil Rubbed Bronze Indooroutdoor regarding sizing 900 X 900

Harbor Breeze Twin Breeze Ii 74 In Oil Rubbed Bronze Indooroutdoor regarding sizing 900 X 900

Ceiling Fan With Two Fans – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it really is taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, according to the room size being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the tools and possible other areas necessary for installing them, their self-assemble kits have anything else. In many cases, the fan, which will have its very own lighting, will replace a ceiling permanent fixture.

Safety, The electricity must be off at the site the place that the fan shall be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker as well as flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed

Installation steps (reading the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this fixture are cold (the test light will always be off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one as well as a white one. Tip: also look at the firmness from the electrical box inside ceiling. If it really is not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box for them. The ceiling fan is heavier than the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires inside junction box cleanly, install the mounting bracket to the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger into the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor as well as a blue or off-color one for your lights to become attached below it. Overlap the stripped ends of these two wires (motor and lights) together with the stripped end from the black ceiling wire inside box, and twist connect them together with the wire nut provided. Connect the white assembly wire to the white ceiling wire much the same way.


Then, to hold these connections from loosening as the fan is working, tape the wide lower ends of these nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box if the box is additionally grounded which has a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an experienced about this green wire connection. Some will say to let it sit be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends from the mounting bracket with the small screws provided. It covers/hides the edges from the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets with the screws and washers provided. Then mount the blades to the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to hold them separate from your rest from the kit hardware.

Tip: to hold the motor from becoming too off-level within this step, install the blades one-by-one opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just underneath the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if the lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with the wall switch, as the fan itself is controlled through the pull-chain switch only, initially set inside off position. Note: The ceiling fan carries a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.

Exit mobile version