Troposair Sunrise 56 In Satin Steel Up Light Ceiling Fan 88600 in size 1000 X 1000Ceiling Fan With Up And Down Light – The flush-style ceiling fan is mounted snugly beside a flat horizontal fairly low ceiling where it’s off the beaten track, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the tools and possible other parts required for installing them, their self-assemble kits include anything else. In many cases, the fan, which will have a unique lighting, will replace a ceiling permanent fixture.
Safety, The electricity has to be off once your there in which the fan is usually to be installed. If the fan is replacing a permanent fixture, power down its fuse or circuit breaker along with flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; don’t lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, as appropriate
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from the ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (the test light will remain off). Cut the wires, leaving 3-5″ of tail allowing you to connect them to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one along with a white one. Tip: also look at the firmness of the electrical box inside the ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, that might require drilling two holes inside the box for them. The ceiling fan is heavier compared to permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside the junction box cleanly, install the mounting bracket towards the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger in the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor along with a blue or off-color one for your lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together using the stripped end of the black ceiling wire inside the box, and twist connect them together using the wire nut provided. Connect the white assembly wire towards the white ceiling wire the same way.
Then, to keep these connections from loosening whilst the fan is working, tape the wide lower ends of those nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) towards the electrical box if the box can be grounded which has a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an expert concerning this green wire connection. Some will say to let it rest be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends of the mounting bracket using the small screws provided. It covers/hides the perimeters of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets using the screws and washers provided. Then mount the blades towards the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to keep them separate from the rest of the kit hardware.
Tip: to keep the motor from becoming too off-level within this step, install the blades one at a time opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just under the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided if the lighting assembly is not wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, whilst the fan itself is controlled through the pull-chain switch only, initially set inside the off position. Note: The ceiling fan has a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.
