Hunter 52 Ceiling Fan – Two reasons to purchase a ceiling fan, air conditioning. If you live in a very cold climate, fans can push hot air gathered near the ceiling down again. Ceiling fans might be simple to install if you have some mechanical aptitude. Current ceiling fans feature remote-controls to vary speed and adjust lighting. If your room already includes a permanent fixture inside the ceiling, your permanent fixture probably has one hot or feed wire likely to it, the neutral white and also the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one for the light the other for the fan motor control and also the neutral and ground. If you just have one Hot wire feeding the ceiling junction box, the remote-control fans will work with your application. Additionally some remote-controlled fans use wall controller which sends its signal on the fan just like a TV remote. It just appears to be a wall control unit. If you only need the energy wire on your remote-controlled fan, please cap over fourth wire which you will not want to make use of. This must be shown inside your directions that had the fan assembly.
Once you might have acquired a fan that suits you, assemble it according on the instructions given. Some fans can be a bit more complex, ask a buddy to help you if you need to. It is best to makes it assembled correctly, using a ceiling fan blade thud you on the pinnacle might be annoying. Once you might have the pre-assembly completed, now you can prepare the ceiling junction box. Of course I know you might have already made sure the energy on the ceiling box is powered down with out it’s possible to energize it accidentally. Once you might have performed this, you ought to find three wires inside the J-box. A copper or green wire for bonding. A white wire for the neutral along with a red or black wire for the power. If your junction box includes a fourth wire, this is build for the wall controlled fan switch that is great and allows you to make use of a non-remote wall controller. I should mention that some all fans feature a wall controllers designed as remotes so do not be confused because these all assist the singular feed inside your ceiling junction box.
A word about weight, not yours but anything regarding the size your fan. If you might have a big fan as well as weighted near 12 pounds or even more, you will need a special junction box that could offer the excess weight. I would recommend i hear you ask someone who knows about these heavier fans you might need what you are likely to install. Most fans are lighter and might be installed in most junction boxes without modifications.
Now let us get up there, the fan that’s. Many fans feature a Hanger the same shape as a U. Install this hanger onto your box, the screws must be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you might have the hanger installed, grab your fan motor minus the blades installed and place it for the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it concurrently. Connect the bonding wire on the chassis as noted inside the instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place while using parts provided. Some have brackets, some make use of a metal plate while some use preformed mounting bases. Use your instructions you may have a fan in no time. Smaller fans may require you to pre-assemble your blades before hanging the fan. I always found installing the motor first and after that installing the blades last is much easier. It does require however, you to work above your face to obtain the blades attached.
Once you might have the fan hanging, the blades installed and everything tightened now you can step over ladder, relax, then install the wall controller as provided. These all vary in design nonetheless they all follow similar procedures. Remember, you will have a line and load situation here. This means, the fishing line side could be the list of wires the feed to the switch box from the panel while the Load side is likely to your fan. This is critical so make sure you comprehend the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be made up on the new controller. Next wire your white neutral on the controllers neutral for the Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire on the Line side of your respective controller. If you might have the fourth wire in there, cap rid of it or use it for the motor control and connect it accordingly for a directions. Red to Red is truly the case here. Once completed, be some Iced Tea and enjoy your new fan.