Kichler Outdoor Ceiling Fans – Two reasons to use a ceiling fan, heating and cooling. If you live in the cold climate, fans can push heated air gathered close to the ceiling back. Ceiling fans may be all to easy to install when you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already features a light fixture inside ceiling, your light fixture probably has one hot or feed wire likely to it, the neutral white and also the bonding green or copper. Essentially this is a three-wire system. Many new construction homes have four wires available, one to the light and something to the fan motor control and also the neutral and ground. If you only have one Hot wire feeding the ceiling junction box, the remote-control fans works with your application. Additionally some remote-controlled fans use wall controller which sends its signal towards the fan as being a TV remote. It just seems like a wall control unit. If you only need the power wire to your remote-controlled fan, please cap off of the fourth wire which you will not need to work with. This needs to be shown within your directions that was included with the fan assembly.
Once you’ve acquired a fan you like, assemble it according towards the instructions given. Some fans can be a much more complex, ask an associate to help if you need to. It is best to help it become assembled correctly, developing a ceiling fan blade thud your self on the head may be annoying. Once you’ve the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you’ve already made certain the power towards the ceiling box is powered down and no one can energize it accidentally. Once you’ve succeeded in doing so, you need to find three wires inside J-box. A copper or green wire for bonding. A white wire to the neutral along with a red or black wire to the power. If your junction box features a fourth wire, this is create to get a wall controlled fan switch which is great and allows you to work with a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so don’t be confused because they all work with the singular feed within your ceiling junction box.
A word about weight, not yours but anything concerning the sized your fan. If you’ve a large fan and its particular weighted near 12 pounds or maybe more, you might need a special junction box that will keep the additional weight. I would recommend i hear you ask someone who knows about these heavier fans if that is what you really are likely to install. Most fans are lighter and may be installed in most junction boxes without modifications.
Now let’s get it there, the fan that is certainly. Many fans come with a Hanger the same shape as a U. Install this hanger on to your box, the screws needs to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you’ve the hanger installed, pick-up your fan motor minus the blades installed and hang it around the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it as well. Connect the bonding wire towards the chassis as noted inside instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place using the parts provided. Some have brackets, some utilize a metal plate although some use preformed mounting bases. Use your instructions and you’ll have a fan quickly. Smaller fans may require that you pre-assemble your blades before hanging the fan. I always found installing the motor first and then installing the blades last is easier. It does require however, that you work above your mind to find the blades attached.
Once you’ve the fan hanging, the blades installed and everything tightened you can now step off of the ladder, take a deep breath, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you’ll have a line and load situation here. This means, the queue side is the group of wires the feed in to the switch box from the panel even though the Load side is likely to your fan. This is critical so make sure you see the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next perform the Line (incoming) side next: Bond or ground should already be comprised towards the new controller. Next wire your white neutral towards the controllers neutral to the Line side. You may have already wired your neutrals together as outlined by your instructions. Now wire your Hot or Power wire towards the Line side of your controller. If you’ve the fourth wire in there, cap it off or use it to the motor control and connect it accordingly for your directions. Red to Red is truly the case here. Once completed, make yourself some Iced Tea and luxuriate in a new fan.