Encon Ceiling Fan – Two reasons to install a ceiling fan, air conditioning. If you live in a very cold climate, fans can push hot air gathered close to the ceiling back off. Ceiling fans can be an easy task to install when you have some mechanical aptitude. Current ceiling fans come with remote-controls to vary speed and adjust lighting. If your room already features a fitting inside the ceiling, your fitting probably has one hot or feed wire going to it, the neutral white along with the bonding green or copper. Essentially this is the three-wire system. Many new construction homes have four wires available, one to the light then one to the fan motor control along with the neutral and ground. If you simply have one Hot wire feeding the ceiling junction box, the remote-control fans will continue to work using your application. Additionally some remote-controlled fans use wall controller which sends its signal towards the fan being a TV remote. It just seems like a wall control unit. If you really need the power wire for your remote-controlled fan, please cap off the fourth wire which you will not need to use. This should be shown inside your directions that was included with the fan assembly.
Once you have acquired an admirer you like, build it according towards the instructions given. Some fans really are a extra complex, ask a pal to aid if necessary. It is best to make sure it is assembled correctly, using a ceiling fan blade thud yourself on the head can be annoying. Once you have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you have already made sure the power towards the ceiling box is powered down and no one can possibly energize it accidentally. Once you have carried this out, you need to find three wires inside the J-box. A copper or green wire for bonding. A white wire to the neutral along with a red or black wire to the power. If your junction box features a fourth wire, this would be set up for any wall controlled fan switch which is great and allows you to use a non-remote wall controller. I should mention that some all fans come with a wall controllers designed as remotes so don’t be confused since these all work with the singular feed inside your ceiling junction box.
A word about weight, not yours but a thing about the sized your fan. If you have a sizable fan and it is weighted near 12 pounds or maybe more, you might need a special junction box that could offer the extra body fat. I would recommend i hear you ask somebody who knows about these heavier fans if that is what you will be going to install. Most fans are lighter and can be installed in most junction boxes without modifications.
Now let’s get it down there, the fan that’s. Many fans come with a Hanger in the shape of a U. Install this hanger on to your box, the screws should be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, get your fan motor devoid of the blades installed and hang up it about the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it simultaneously. Connect the bonding wire towards the chassis as noted inside the instructions. Next connect the white neutral wire, and now the black wire. Swing the fan into place using the parts provided. Some have brackets, some work with a metal plate and some use preformed mounting bases. Use your instructions and you will have an admirer quickly. Smaller fans may require that you pre-assemble your blades before hanging the fan. I always found installing the motor first after which installing the blades last is less difficult. It does require however, that you work above your mind to obtain the blades attached.
Once you have the fan hanging, the blades installed and everything tightened you can now step off the ladder, take a deep breath, then install the wall controller as provided. These all vary in design but they all follow similar procedures. Remember, you’ll have a line and load situation here. This means, the queue side will be the group of wires the feed to the switch box through the panel as the Load side is going to your fan. This is critical so be sure you comprehend the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be composed towards the new controller. Next wire your white neutral towards the controllers neutral to the Line side. You may have already wired your neutrals together in accordance with your instructions. Now wire your Hot or Power wire towards the Line side of your controller. If you have the fourth wire in that room, cap them back or use it to the motor control and connect it accordingly to your directions. Red to Red is usually the case here. Once completed, be some Iced Tea and enjoy a new fan.