Hugger Ceiling Fan No Light – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it can be out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the equipment and possible the rest necessary for installing them, their self-assemble kits have everything else. In many cases, the fan, that may have its very own lighting, will replace a ceiling permanent fixture.
Safety, The electricity must be off once your there the place that the fan shall be installed. If the fan is replacing a permanent fixture, shut down its fuse or circuit breaker as well as flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or end up in a twisted position while there. Also, wear protective eye-glasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eye-glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if required
Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the permanent fixture from your ceiling. With the electricity off, slowly remove the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to the fixture are cold (quality light will stay off). Cut the wires, leaving 3-5″ of tail allowing you to connect these phones the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness in the electrical box inside ceiling. If it can be not solidly connected to the ceiling, add two extra screws to its top side, that might require drilling two holes inside box for the children. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket to the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor plus a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of these two wires (motor and lights) together with all the stripped end in the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same.
Then, to maintain these connections from loosening whilst the fan is working, tape the wide lower ends of these nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) to the electrical box if your box is also grounded which has a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an expert about this green wire connection. Some will say to let it sit be, i.e., do nothing by it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends in the mounting bracket with all the small screws provided. It covers/hides the edges in the motor and the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets with all the screws and washers provided. Then mount the blades to the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate from your rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level within this step, install the blades one-by-one opposite together in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades via the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly just isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with all the wall switch, whilst the fan itself is controlled by the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch that enables the draft either to go upward or downward as preferred. For more information on ceiling fan installation, see the following sites.