Bulbs Ideas

Small Black Ceiling Fan

Westinghouse Wengue 30 In Indoor Espresso Ceiling Fan 7224500 The with proportions 1000 X 1000

Westinghouse Wengue 30 In Indoor Espresso Ceiling Fan 7224500 The with proportions 1000 X 1000

Small Black Ceiling Fan – The flush-style ceiling fan is mounted snugly next to a flat horizontal fairly low ceiling where it is dealt with, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of room being fitted, and will cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the instruments and possible other regions essential for installing them, their self-assemble kits have anything else. In many cases, the fan, that can have a unique lighting, will replace a ceiling light fixture.

Safety, The electricity should be off at the site the place that the fan is usually to be installed. If the fan is replacing a light fixture, shut down its fuse or circuit breaker together with flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or get into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if necessary

Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture from the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from the electrical junction box in the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to the fixture are cold (quality light will continue to be off). Cut the wires, leaving 3-5″ of tail for connecting the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one and a white one. Tip: also look into the firmness of the electrical box in the ceiling. If it is not solidly coupled to the ceiling, add two extra screws to its top side, that might require drilling two holes in the box for them. The ceiling fan is heavier than the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires in the junction box cleanly, install the mounting bracket for the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should certainly swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of such two wires (motor and lights) together with the stripped end of the black ceiling wire in the box, and twist connect them together with the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same.


Then, to keep these connections from loosening while the fan is working, tape the wide lower ends of such nuts for their wires with electrical tape. Also, attach the green fan wire (ground wire from the bracket frame) for the electrical box if the box is also grounded with a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an expert concerning this green wire connection. Some will say to let it rest be, i.e., do nothing at all with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends of the mounting bracket with the small screws provided. It covers/hides the sides of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades for their end brackets with the screws and washers provided. Then mount the blades for the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to keep them separate from the rest of the kit hardware.

Tip: to keep the motor from becoming too off-level during this step, install the blades individually opposite to one another to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders in the order instructed. Note: a housing cap is provided if the lighting assembly isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with the wall switch, while the fan itself is controlled from the pull-chain switch only, initially set in the off position. Note: The ceiling fan carries a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.

Exit mobile version