Ceiling Fan Dimmer – The flush-style ceiling fan is mounted snugly close to a set horizontal fairly low ceiling where it really is out of the way, and where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the size of the room being fitted, which enable it to cost typically from $30 to $300. It generally has three fan motor speeds, which can be reversible. Except for the various tools and possible the rest required for installing them, their self-assemble kits have anything else. In many cases, the fan, that may have a unique lighting, will replace a ceiling fitting.
Safety, The electricity have to be off to begin the place that the fan shall be installed. If the fan is replacing a fitting, power down its fuse or circuit breaker as well as flipping its wall exchange signal of the off position. Stand on a sturdy wide-berth step stool or ladder in the installation; tend not to lean or get into a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and extra screws for securing the junction box, if needed
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the fitting in the ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws in the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to the fixture are cold (test light will continue to be off). Cut the wires, leaving 3-5″ of tail allowing you to connect the crooks to the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one along with a white one. Tip: also look into the firmness in the electrical box inside ceiling. If it really is not solidly attached to the ceiling, add two extra screws to its top side, that might require drilling two holes inside box on their behalf. The ceiling fan is heavier than the fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger into the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor along with a blue or off-color one to the lights to get attached below it. Overlap the stripped ends of the two wires (motor and lights) together using the stripped end in the black ceiling wire inside box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire exactly the same.
Then, to hold these connections from loosening even though the fan is working, tape the wide lower ends of the nuts on their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) for the electrical box if your box can also be grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a professional concerning this green wire connection. Some will say to let it rest be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends in the mounting bracket using the small screws provided. It covers/hides the perimeters in the motor along with the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After seeking the top or bottom reversible blade color scheme preferred, attach the blades on their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to hold them separate in the rest in the kit hardware.
Tip: to hold the motor from becoming too off-level in this step, install the blades one by one opposite to each other to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly just isn’t wanted for any reason. 8. Test the fan and lights. After turning the electricity back on, flip the wall exchange signal of on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on using the wall switch, even though the fan itself is controlled with the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.