Bulbs Ideas

Ceiling Fan Accessories

Four Winds 54 In White Ceiling Fan Replacement Switch Cup 247926012 for proportions 1000 X 1000

Four Winds 54 In White Ceiling Fan Replacement Switch Cup 247926012 for proportions 1000 X 1000

Ceiling Fan Accessories – The flush-style ceiling fan is mounted snugly beside a designated horizontal fairly low ceiling where it can be dealt with, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the equipment and possible other regions needed for installing them, their self-assemble kits feature everything else. In many cases, the fan, that can have a unique lighting, will replace a ceiling light fixture.

Safety, The electricity should be off at the site where the fan is usually to be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker as well as flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; usually do not lean or get into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if necessary

Installation steps (seeing the fan installation instructions thoroughly). 1. Remove the light fixture in the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws in the electrical junction box within the ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect them to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one and a white one. Tip: also confirm the firmness from the electrical box within the ceiling. If it can be not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes within the box for the kids. The ceiling fan is heavier than the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends from the tailing wires within the junction box cleanly, install the mounting bracket on the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside from the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder from the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor and a blue or off-color one for the lights to become attached below it. Overlap the stripped ends of the two wires (motor and lights) together with all the stripped end from the black ceiling wire within the box, and twist connect them together with all the wire nut provided. Connect the white assembly wire on the white ceiling wire much the same way.


Then, to help keep these connections from loosening as the fan is working, tape the wide lower ends of the nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) on the electrical box if your box can also be grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to get forced out be, i.e., relax from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud on the far ends from the mounting bracket with all the small screws provided. It covers/hides the edges from the motor along with the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets with all the screws and washers provided. Then mount the blades on the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed on the motor to help keep them separate in the rest from the kit hardware.

Tip: to help keep the motor from becoming too off-level during this step, install the blades individually opposite to one another to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly on the small round central housing unit just below the fan blades through the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders within the order instructed. Note: a housing cap is provided if your lighting assembly is just not wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set in the future on with all the wall switch, as the fan itself is controlled from the pull-chain switch only, initially set within the off position. Note: The ceiling fan carries a reversible motor switch that permits the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.

Exit mobile version