Ceiling Fan With Mason Jar Lights – The flush-style ceiling fan is mounted snugly alongside an appartment horizontal fairly low ceiling where it can be out of the way, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, depending on the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, which are reversible. Except for the various tools and possible the rest needed for installing them, their self-assemble kits have the rest. In many cases, the fan, that can have its own lighting, will replace a ceiling fitting.
Safety, The electricity has to be off once your there the location where the fan shall be installed. If the fan is replacing a fitting, de-activate its fuse or circuit breaker together with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; tend not to lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring is needed, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if necessary
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the fitting in the ceiling. With the electricity off, slowly get rid of the shade, bulbs, and fixture screws in the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, make sure the wire connections to this particular fixture are cold (the test light will always be off). Cut the wires, leaving 3-5″ of tail for connecting these to the ceiling fan motor assembly. If the house is old, only two wires might exist, a black one plus a white one. Tip: also check the firmness in the electrical box inside ceiling. If it can be not solidly attached to the ceiling, add two extra screws to its top side, which might require drilling two holes inside box on their behalf. The ceiling fan is heavier as opposed to fitting. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket to the box with the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly really should swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor plus a blue or off-color one to the lights to be attached below it. Overlap the stripped ends of such two wires (motor and lights) together with the stripped end in the black ceiling wire inside box, and twist connect them together with the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of such nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) to the electrical box if the box can be grounded using a third bare or green wire. Otherwise, if the electrical box in not grounded, ask an expert relating to this green wire connection. Some will say to let it sit be, i.e., do nothing at all by using it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends in the mounting bracket with the small screws provided. It covers/hides the edges in the motor and the wiring and ceiling box. 6. Assemble the fan blades (four to six) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with the screws and washers provided. Then mount the blades to the bottom side of fan motor with the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to maintain them separate in the rest in the kit hardware.
Tip: to maintain the motor from becoming too off-level with this step, install the blades one by one opposite to each other to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if the lighting assembly is just not wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set ahead on with the wall switch, as the fan itself is controlled with the pull-chain switch only, initially set inside off position. Note: The ceiling fan features a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.