48 Inch Outdoor Ceiling Fan – Two good reasons to use a ceiling fan, heating and cooling. If you live in the cold climate, fans can push hot air gathered at the ceiling back down. Ceiling fans may be simple to install for those who have some mechanical aptitude. Current ceiling fans include remote-controls to vary speed and adjust lighting. If your room already features a fitting inside the ceiling, your fitting probably has one hot or feed wire going to it, the neutral white and also the bonding green or copper. Essentially this is a three-wire system. Many new construction homes have four wires available, one to the light and one to the fan motor control and also the neutral and ground. If you just have one Hot wire feeding the ceiling junction box, the remote-control fans works using your application. Additionally some remote-controlled fans use wall controller which sends its signal to the fan as being a TV remote. It just appears to be a wall control unit. If you just have the power wire on your remote-controlled fan, please cap off the fourth wire which you will not require to work with. This needs to be shown with your directions that was included with the fan assembly.
Once you have acquired a follower you prefer, put it together according to the instructions given. Some fans are a much more complex, ask an associate to assist if you need to. It is best to make sure it is assembled correctly, having a ceiling fan blade thud your self on the pinnacle may be annoying. Once you have the pre-assembly completed, you can now prepare the ceiling junction box. Of course I know you have already ensured the power to the ceiling box is deterred with out one can possibly energize it accidentally. Once you have performed this, you should find three wires inside the J-box. A copper or green wire for bonding. A white wire to the neutral along with a red or black wire to the power. If your junction box features a fourth wire, this is setup for any wall controlled fan switch that is great and allows you to work with a non-remote wall controller. I should mention that some all fans include a wall controllers designed as remotes so do not be confused because they all work with the singular feed with your ceiling junction box.
A word about weight, not yours but a word in regards to the height and width of your fan. If you have a sizable fan and its weighted near 12 pounds or even more, you will need a special junction box that may support the more weight. I would recommend i hear you ask somebody who knows about these heavier fans recommendations what you really are going to install. Most fans are lighter and may be set up in most junction boxes without modifications.
Now let us get it down there, the fan that is. Many fans include a Hanger shaped like a U. Install this hanger on to your box, the screws needs to be 8/32 types. That means a size 8 diameter or gauge screw with 32 threads per inch. Once you have the hanger installed, pick-up your fan motor devoid of the blades installed and place it around the hanger. This allows you the electrician to hook up the wires without struggling to juggle the motor and wire it simultaneously. Connect the bonding wire to the chassis as noted inside the instructions. Next connect the white neutral wire, and after this the black wire. Swing the fan into place with all the parts provided. Some have brackets, some utilize a metal plate although some use preformed mounting bases. Use your instructions you may have a follower in no time. Smaller fans may require one to pre-assemble your blades before hanging the fan. I always found installing the motor first after which installing the blades last is much easier. It does require however, one to work above your head to find the blades attached.
Once you have the fan hanging, the blades installed and everything tightened you can now step off the ladder, breathe deeply, then install the wall controller as provided. These all vary in design however they all follow similar procedures. Remember, you will find a line and load situation here. This means, the line side is the pair of wires the feed in the switch box in the panel whilst the Load side is going to your fan. This is critical so be sure to view the difference. Connect the Load side first: Connect your bonding wire first. Then connect your white neutral wire. Then your hot wire. Next do the Line (incoming) side next: Bond or ground should already be constructed to the new controller. Next wire your white neutral to the controllers neutral to the Line side. You may have already wired your neutrals together in accordance with your instructions. Now wire your Hot or Power wire to the Line side of your respective controller. If you have the fourth wire inside, cap rid of it or use it to the motor control and connect it accordingly to your directions. Red to Red is often the case here. Once completed, be some Iced Tea and luxuriate in your fan.