Hampton Bay Metarie 24 In Indoor White Ceiling Fan With Light Kit intended for dimensions 1000 X 100024 Inch Ceiling Fan With Light – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it’s out of the way, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with respect to the room size being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the tools and possible other areas needed for installing them, their self-assemble kits include anything else. In many cases, the fan, which will have its own lighting, will replace a ceiling light fixture.
Safety, The electricity has to be off to begin the location where the fan is usually to be installed. If the fan is replacing a light fixture, shut down its fuse or circuit breaker in addition to flipping its wall switch to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; don’t lean or end up in a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is required, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if necessary
Installation steps (looking at the fan installation instructions thoroughly). 1. Remove the light fixture through the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws through the electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, ensure that the wire connections to this fixture are cold (the test light will stay off). Cut the wires, leaving 3-5″ of tail for connecting these phones the ceiling fan motor assembly. If the property is old, only two wires might exist, a black one plus a white one. Tip: also look at the firmness in the electrical box inside ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which could require drilling two holes inside box for them. The ceiling fan is heavier compared to the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends in the tailing wires inside junction box cleanly, install the mounting bracket to the box with all the two 5/32″ screw-bolts provided. Let the tailing wires hang outside in the bracket. 3. Hang the motor assembly through the bracket. Insert the topside motor-hanger in to the centralized holder in the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly should really swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for your motor plus a blue or off-color one for your lights to become attached below it. Overlap the stripped ends of those two wires (motor and lights) together with all the stripped end in the black ceiling wire inside box, and twist connect them together with all the wire nut provided. Connect the white assembly wire to the white ceiling wire exactly the same.
Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire through the bracket frame) to the electrical box if your box is additionally grounded which has a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist relating to this green wire connection. Some will say to get forced out be, i.e., do nothing at all from it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud to the far ends in the mounting bracket with all the small screws provided. It covers/hides the perimeters in the motor as well as the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After choosing the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets with all the screws and washers provided. Then mount the blades to the bottom side of fan motor with all the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed to the motor to help keep them separate through the rest in the kit hardware.
Tip: to help keep the motor from becoming too off-level in this step, install the blades individually opposite together to begin with. 7. Install the lighting assembly. Attach the fan’s lighting assembly to the small round central housing unit just below the fan blades using the quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch to on. Set the pull-chain switches as desired. Often, the fan lighting is set into the future on with all the wall switch, even though the fan itself is controlled with the pull-chain switch only, initially set inside off position. Note: The ceiling fan has a reversible motor switch that allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, begin to see the following sites.
