Dual Ceiling Fan – The flush-style ceiling fan is mounted snugly close to a flat horizontal fairly low ceiling where it’s dealt with, and from which it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of room being fitted, and may cost typically from $30 to $300. It generally has three fan motor speeds, that happen to be reversible. Except for the various tools and possible other regions required for installing them, their self-assemble kits include anything else. In many cases, the fan, that will have its own lighting, will replace a ceiling light fixture.
Safety, The electricity have to be off once your there where the fan shall be installed. If the fan is replacing a light fixture, de-activate its fuse or circuit breaker together with flipping its wall switch the signal from the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; don’t lean or enter a twisted position while there. Also, wear protective eye glasses or goggles. Furthermore, if additional auxiliary household wiring is necessary, get professional advice or help first. Tools needed, instructions (electrical) eye glasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and additional screws for securing the junction box, if necessary
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the light fixture from your ceiling. With the electricity off, slowly take away the shade, bulbs, and fixture screws from your electrical junction box inside ceiling. Let the skeleton fixture hang there. With the light tester, guarantee the wire connections to this fixture are cold (test light will continue to be off). Cut the wires, leaving 3-5″ of tail for connecting the crooks to the ceiling fan motor assembly. If the residence is old, only two wires might exist, a black one along with a white one. Tip: also look into the firmness of the electrical box inside ceiling. If it’s not solidly coupled to the ceiling, add two extra screws to its top side, which can require drilling two holes inside box on their behalf. The ceiling fan is heavier compared to the light fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside junction box cleanly, install the mounting bracket for the box using the two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly from your bracket. Insert the topside motor-hanger in to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one for the motor along with a blue or off-color one for the lights to get attached below it. Overlap the stripped ends of those two wires (motor and lights) together using the stripped end of the black ceiling wire inside box, and twist connect them together using the wire nut provided. Connect the white assembly wire for the white ceiling wire much the same way.
Then, to maintain these connections from loosening as the fan is working, tape the wide lower ends of those nuts to their wires with electrical tape. Also, attach the green fan wire (ground wire from your bracket frame) for the electrical box if your box can be grounded having a third bare or green wire. Otherwise, if your electrical box in not grounded, ask a specialist about this green wire connection. Some will say to leave it be, i.e., do nothing with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud for the far ends of the mounting bracket using the small screws provided. It covers/hides the perimeters of the motor and the wiring and ceiling box. 6. Assemble the fan blades (4 to 6) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades to their end brackets using the screws and washers provided. Then mount the blades for the bottom side of fan motor using the bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed for the motor to maintain them separate from your rest of the kit hardware.
Tip: to maintain the motor from becoming too off-level within this step, install the blades one-by-one opposite together to start with. 7. Install the lighting assembly. Attach the fan’s lighting assembly for the small round central housing unit just beneath the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside order instructed. Note: a housing cap is provided if your lighting assembly isn’t wanted at all. 8. Test the fan and lights. After turning the electricity back on, flip the wall switch the signal from on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on using the wall switch, as the fan itself is controlled from the pull-chain switch only, initially set inside off position. Note: The ceiling fan includes a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, understand the following sites.