Harbor Breeze Off White Handheld Universal Ceiling Fan Remote with dimensions 900 X 900Harbor Breeze Ceiling Fan Remote Control – The flush-style ceiling fan is mounted snugly alongside a set horizontal fairly low ceiling where it is taken care of, and from where it delivers a comforting room breeze. It comes in several diameters, from about 28 to 60-inches, with regards to the size of the room being fitted, and can cost typically from $30 to $300. It generally has three fan motor speeds, that are reversible. Except for the tools and possible the rest necessary for installing them, their self-assemble kits have everything else. In many cases, the fan, that will have its lighting, will replace a ceiling permanent fixture.
Safety, The electricity should be off once your there where the fan is to be installed. If the fan is replacing a permanent fixture, de-activate its fuse or circuit breaker together with flipping its wall change to the off position. Stand on a sturdy wide-berth step stool or ladder during the installation; do not lean or enter into a twisted position while there. Also, wear protective eyeglasses or goggles. Furthermore, if additional auxiliary household wiring should be used, get professional advice or help first. Tools needed, instructions (electrical) eyeglasses or goggles step-stool/ladder Phillips screwdrivers pliers electrical tape knife or sissors AC tester light wire cutter/stripper tape measure (optional) electric drill and further screws for securing the junction box, if needed
Installation steps (after reading the fan installation instructions thoroughly). 1. Remove the permanent fixture in the ceiling. With the electricity off, slowly eliminate the shade, bulbs, and fixture screws in the electrical junction box inside the ceiling. Let the skeleton fixture hang there. With the light tester, ensure the wire connections for this fixture are cold (the exam light will remain off). Cut the wires, leaving 3-5″ of tail in order to connect these to the ceiling fan motor assembly. If the home is old, only two wires might exist, a black one as well as a white one. Tip: also check the firmness of the electrical box inside the ceiling. If it is not solidly attached to the ceiling, add two extra screws to its top side, which could require drilling two holes inside the box for the children. The ceiling fan is heavier compared to the permanent fixture. It also wobbles slightly during operation. 2. Install the mounting bracket. After stripping the ends of the tailing wires inside the junction box cleanly, install the mounting bracket towards the box while using two 5/32″ screw-bolts provided. Let the tailing wires hang outside of the bracket. 3. Hang the motor assembly in the bracket. Insert the topside motor-hanger to the centralized holder of the bracket. Insert the plastic lock clip that holds it into place. Note: the hanging motor assembly is supposed to swivel slightly. 4. Connect the wiring. Generally, the motor assembly has two so-called hot wires, a black one to the motor as well as a blue or off-color one to the lights to be attached below it. Overlap the stripped ends of these two wires (motor and lights) together while using stripped end of the black ceiling wire inside the box, and twist connect them together while using wire nut provided. Connect the white assembly wire towards the white ceiling wire exactly the same.
Then, to help keep these connections from loosening even though the fan is working, tape the wide lower ends of these nuts with their wires with electrical tape. Also, attach the green fan wire (ground wire in the bracket frame) towards the electrical box when the box is also grounded which has a third bare or green wire. Otherwise, when the electrical box in not grounded, ask a specialist about it green wire connection. Some will say to let it sit be, i.e., relax with it. Others could suggest further wiring? 5. Install the flush-mount motor shroud. Install the motor shroud towards the far ends of the mounting bracket while using small screws provided. It covers/hides the sides of the motor and also the wiring and ceiling box. 6. Assemble the fan blades (3 to 4) and mount them. After picking out the top or bottom reversible blade color scheme preferred, attach the blades with their end brackets while using screws and washers provided. Then mount the blades towards the bottom side of fan motor while using bolts, lock washers, and dampening gaskets provided. Note: these latter pieces sometimes are partially pre-installed towards the motor to help keep them separate in the rest of the kit hardware.
Tip: to help keep the motor from becoming too off-level with this step, install the blades one-by-one opposite together in the first place. 7. Install the lighting assembly. Attach the fan’s lighting assembly towards the small round central housing unit just under the fan blades through quick-wire-connectors and small screws provided. Install the glass shades, bulbs, and pull-chain extenders inside the order instructed. Note: a housing cap is provided when the lighting assembly just isn’t wanted unconditionally. 8. Test the fan and lights. After turning the electricity back on, flip the wall change to on. Set the pull-chain switches as desired. Often, the fan lighting is set to come on while using wall switch, even though the fan itself is controlled from the pull-chain switch only, initially set inside the off position. Note: The ceiling fan has a reversible motor switch which allows the draft either to go upward or downward as preferred. For more information on ceiling fan installation, start to see the following sites.
